[SYSTEM]

DMASingleByteMode=OFF

[DRIVER]
; Interpolation method used in Enhanced full duplex, ( Linear or Filter )
Interp8=Linear 
Interp16=Linear
SaveSettingsOnExit=ON

[APPLETS]

InputControlPath=
InputApplet=ASB16INP.EXE
IPAllwaysOnTop=OFF
IPAlwaysOnTop=OFF
OutputControlPath=
OutputApplet=ASB16OUT.EXE
OPAllwaysOnTop=OFF
OPAlwaysOnTop=OFF

[MIXER]
; Line ( LINE ) or microphone ( MIC ) selected as input
InputSelection=LINE

; Line input gain. 0 to 65535=0 to 22.5 db gain
lLineVolume=0
rLineVolume=0
LineGang=ON
LineMute=ON

; Mic input gain. 0 to 65535=0 to 22.5 db gain
lMicVolume=0
rMicVolume=0
MicGang=ON
MicMute=ON

; Aux input gain. 0 to 65535=0 to 22.5 db gain
lAuxInVolume=0
rAuxInVolume=0
AuxInGang=ON
AuxInMute=OFF

; Loop back input gain. 0 to 65535=0 to 22.5 db gain
lLoopBackInputVolume=0
rLoopBackInputVolume=0
LoopBackInputGang=ON
LoopBackInputMute=ON


; Monitor attenuation. 0 - 65535=mute to no attenuation. 

MonitorVolume=0
MonitorMute=ON
MonitorMode=Recording

; CS4215 output atten setting. 0 - 65535=full attenuation to no attenuation in 
; 32 1.5 Db steps.

lMasterVolume=64494
rMasterVolume=64494
MasterMute=OFF
MasterGang=ON

; Aux Volume setting 0 - 65535. 0=full attenuation, 65535 = no attenuation.
lAuxVolume=64494
rAuxVolume=64494
AuxMute=OFF
AuxGang=ON

; Aux2 volume setting 0 - 65535. 0=full attenuation, 65535 = no attenuation.

lAux2Volume=64494
rAux2Volume=64494
Aux2Mute=OFF
Aux2Gang=ON

; Line Mix volume setting 0 - 65535. 0=full attenuation, 65535 = no attenuation.

lLineMixVolume=0
rLineMixVolume=0
LineMixMute=ON
LineMixGang=ON

; Mono Mix volume setting 0 - 65535. 0=full attenuation , 65535 = no attenuation.

MonoVolume=0
MonoMute=ON

; MonoOutMute indicates the state of the mono output mute.
MonoOutMute=ON

; MicBoost indicates if 20db additional boost is added when the mic input is selected.
MicBoost=OFF

; Mic AGC
MicAGC=OFF

;HWMUTE=0,1,E

; Virtual Volume master
lVirtMaster=57078
rVirtMaster=57078
VirtMasterMute=OFF
VirtMasterGang=ON

LowPriInputSelection=MIC
lLowPriMicVolume=0
rLowPriMicVolume=0
LowPriMicBoost=OFF
lLowPriLineVolume=0
rLowPriLineVolume=0
lLowPriLoopBackInputVolume=0
rLowPriLoopBackInputVolume=0
lLowPriAuxInVolume=0
rLowPriAuxInVolume=0

[RECORD]
; HighPassFilter ON or OFF, when on will reduce signal offset at the expense of slightly
; lower fidelity ( probably not audible ) at low frequencies.
HighPassFilter=ON

; The default dither state.  This may be over-ridden at some record formats.
Dither=ON

; VU meter  section
[Meter]

; Tells the control panel to come up running the VU meter when the inputs dialog is shown.
MeterDisplay=ON

; DecayRate defines how quickly the VU meter bars decay
; 0=no decay, 255=immediate and full decay. default = 16.
DecayRate=16

; The number of time / second that the VU meter will update. default=10.
VUUpdateRate=10

[AGC]
; The desired interrupt rate used when AGC is active and capturing.
IntsPerSec=50

; The number of interrupts which must occur before a bit of gain can
; be added to the input gain.
IntsPerBitofDecay=8

; This hex entry describes the level that the AGC code is trying to 
; get the input signal average to equal.
Target=A00

[CONTROLS]
; This section dictates the controls which will be present on a WSS mixer.

;****************************************** 
;* Mixer Lines To include
;****************************************** 

;MixerSources=Line,Aux1,Aux2,Mono,Monitor,Wave
MixerSources=Line,Aux1,Aux2,Wave

;****************************************** 
;* Input Lines To include
;****************************************** 

;InputSources=Mic,Aux1,Line,Loop
InputSources=Mic,Aux1,Line,Loop

;********************************************************** 
;* Line Source Descriptions ( short/long names )
;********************************************************** 

ShortNameLine=Synth
LongNameLine=Synthesiser
ShortNameAux1=Line
LongNameAux1=Line Input
ShortNameAux2=CD
LongNameAux2=Compact Disk
ShortNameMono=Phone
LongNameMono=Telephone
ShortNameMonitor=Mix
LongNameMonitor=Mixer Output
ShortNameWave=Wav
LongNameWave=Digital Output
ShortNameMic=Mic
LongNameMic=Microphone
ShortNameLoopback=Loop
LongNameLoopback=Digital Loopback

;********************************************************** 
;* Thing connected to Sources entries
;********************************************************** 

; These are the possible assignment values:
;       Undefined, Digital, Line, Microphone, Synthesizer
;       CompactDisk, Telephone, PCSpeaker, WaveOut, Auxiliary, Analog 

SourceForLine=Synthesizer
SourceForAux1=Line
SourceForAux2=CompactDisk
SourceForMono=Telephone
SourceForMic=Microphone

[Speakerphone]
SpeakerFeedback=5
HybridFeedback=57